Default Password for Netgear WGR614v10 Genie Router

To get access to Netgear WGR614v10 Genie router, you need the login IP address of your router, the username, and password.

You can find these information in Netgear WGR614v10 Genie router manual. But if you do not have the manual for your router, then you can use the quick guide below.

Login to the Netgear WGR614v10 Genie Router

The Netgear WGR614v10 Genie has a web interface for configuration. You can use any web browser to log in to the Netgear WGR614v10 Genie router.

Put the IP Address(without “http://” or “https://”) of your Netgear WGR614v10 Genie in the Address Bar of your web browser. Then press the Enter key on your keyboard. You should see a dialog box pop up asking you for your Netgear WGR614v10 Genie login data.

Default login data for Netgear WGR614v10 Genie

You need to know the username and password to log in to your Netgear WGR614v10 Genie router. We listed below.

ModelIpUsername & Password
Netgear WGR614v10 Genie192.168.1.1Username:admin/ Password:password

Note: If you are using the default settings you should change them to increase security and prevent unauthorized access to your network.

Other Netgear WGR614v10 Genie Login Problems

If you can’t get a login to your router, here are a few possible solutions you can try.

The Password of Netgear WGR614v10 Genie Doesn’t Work

It would be best if you tried the other same brands’ passwords.

Perhaps your router’s default password is differs from what we have listed here.

Some Brands will set a different Complex password that is difficult to remember, and then printed on the label of the router.

What if forgot password to Netgear WGR614v10 Genie router?

If your Internet Service Provider supplied you with your router then you might want to try giving them a call, and see if they either know what your router’s username and password are, or maybe they can reset it for you.

How to Reset the Netgear WGR614v10 Genie Router To Default Settings?

If you still can’t get logged in, then you are probably going to reset your router to its default settings.

To do this, press and hold the Reset button for 10 seconds. It may be an aperture or a button and will be clearly marked.

Change Netgear WGR614v10 Genie Default Wifi Name (SSID)

By default, some Netgear WGR614v10 Genie routers have network names (with the manufacturer name). We recommend using a personalized name because a default name unnecessarily identifies your router’s brand, which makes it easier for hackers.

Configure Wireless MAC address filter for Netgear WGR614v10 Genie

MAC filtering allows you to restrict access to your Netgear WGR614v10 Genie router. To enable this feature, enter the 12 digit MAC ID of each computer connected to your network into your Netgear WGR614v10 Genie router. Be sure to update this information when adding devices.

How to configure:

  1. Open the web browser and type the 192.168.1.1 on the address.
  2. Enter the username and password for Netgear WGR614v10 Genie router.
  3. Go to the MAC List page, you can find the MAC address of all the devices which are connected to the router.
  4. Go to Wireless->Wireless MAC Filtering page, click the Add New button.
  5. Type in the MAC address you want to allow or deny to access the router, and give a description for this item.
  6. The status should be Enabled and at last, click the Save button.
Rate article
Add a comment

four × 3 =

  1. Chester Maria

    Thank goodness!

    Reply
  2. Coral Richards

    Yes, It works…

    Reply
  3. Matthew IV.

    While I searched all over the world for the default password of this damn router, I find it here.

    Reply